一种“KooN”结构的马尔可夫简并建模和简化计算的方法

IEC61508等标准提出了几种计算安全仪表系统需求时平均失效概率的方法,但是,对于具有冗余配置的复杂系统,随着组件数量的增加,系统的中间状态数量快速增长,用户难以构建马尔可夫模型,即便借助计算机来建模运算也较为耗时。提出了一种同型“K oo N”简并状态的马尔可夫建模的通用方法,首先是根据降级状态进行判断,将符合条件的状态进行简并,然后对标记为危险失效状态的概率进行计算。通过严格的理论推导,该简并状态方法可以在不损失精度的前提下简化马尔可夫建模。     

Effect of ultrasonic waveforms on gas–liquid mass transfer in microreactors

This study aims to investigate the effect of ultrasonic waveforms on the gas–liquid mass transfer process. For a given load power (P), continuous rectangular wave yielded stronger bubble oscillation and higher mass transfer coefficient (k_La) than continuous triangular and sinusoidal wave. For pulsed ultrasound, the k_La decreased monotonically with decreasing duty ratio (D), resulting in weak enhancement at low D (≤33%). For a given average load power (P_A), concentrating the P for a shorter period resulted in a higher k_La due to stronger cavitation behavior. For a given P_A and D, decreasing the pulse period (T) led to an increase in k_La, which reached a constant high level when the T fell below a critical value. By optimizing the D and T, a k_La equivalent to 92% of that under continuous ultrasound was obtained under pulsed ultrasound at a D of 67%, saving 33% in power consumption.     

IRS辅助的SWIPT系统中基于能效优先的波束成形设计与优化

以智能反射面(intelligent reflecting surface,IRS)辅助的无线携能通信(simultaneous wireless information and power transfer,SWIPT)系统为背景,研究了该系统中基于能效优先的多天线发送端有源波束成形与IRS无源波束成形联合设计与优化方法。以最大化接收端的最小能效为优化目标,构造在发送端功率、接收端能量阈值、IRS相移等多约束下的非线性优化问题,用交替方向乘子法(alternating direction method of multipliers,ADMM)求解。采用Dinkelbach算法转化目标函数,通过奇异值分解(singular value decomposition,SVD)和半定松弛(semi-definite relaxation,SDR)得到发送端有源波束成形向量。采用SDR得到IRS相移矩阵与反射波束成形向量。结果表明,该系统显著降低了系统能量收集(energy harvesting,EH)接收端的能量阈值。当系统总电路功耗为?15 dBm时,所提方案的用户能效为300 KB/J。当IRS反射阵源数与发送天线数均为最大值时,系统可达最大能效。     

Life cycle assessment of HFC-134a production by calcium carbide acetylene route in China

HFC-134a is a widely used environment-friendly refrigerant. At present, China is the largest producer of HFC-134a in the world. The production of HFC-134a in China mainly adopts the calcium carbide acetylene route. However, the production route has high resource and energy consumption and large waste emission, and few of the studies addressed on the environmental performance of its production process. This study quantified the environmental performance of HFC-134a production by calcium carbide route via carrying out a life cycle assessment (LCA) using the CML 2001 method. And uncertainty analysis by Monte-Carlo simulation was also carried out. The results showed that electricity had the most impact on the environment, followed by steam, hydrogen fluoride and chlorine, and the impact of direct CO₂ emissions in calcium carbide production stage on the global warming effect also could not be ignored. Therefore, the clean energy (e.g., wind, solar, biomass, and natural gas) was used to replace coal-based electricity and coal-fired steam in this study, showing considerable environmental benefits. At the same time, the use of advanced production technologies could also improve environmental benefits, and the environmental impact of the global warming category could be reduced by 4.1% via using CO₂ capture and purification technology. The Chinese database of HFC-134a production established in this study provides convenience for the relevant study of scholars. For the production of HFC-134a, this study helps to better identify the specific environmental hotspots and proposes useful ways to improve the environmental benefits.     

基于音频特征的工程车辆工况识别研究

高效率地使用工程车辆是工程项目管理中节约成本的有效方法，无人监管环境下工程车辆的工况识别，是实现工程车辆高效率使用的有效手段。目前以GPS等技术为核心的车辆智能管理系统未对工程车辆进行工况识别，提出一种基于GRU循环神经网络的工程车辆工况识别方法，通过对工程车辆在不同工况下产生的音频信号进行分析，从中提取Mel倒谱系数作为主要特征，构建GRU循环神经网络模型进行训练和识别。实验结果表明，该方法可以实现对工程车辆工况的有效识别。     

电感耦合等离子体质谱法测定大气降水中钠的不确定度评定

采用电感耦合等离子体质谱仪测定大气降水样品中的钠元素，并依据不确定度的评定与表示方法对分析过程中存在的不确定度来源如：标准溶液配制、校准曲线拟合、样品重复测定等各个环节进行探讨和评定，找出影响不确定度的主要因素。最终给出降水样品的合成扩展不确定度，降水样品的钠的浓度表示为(3.934±0.550)mg/L,k=2,从而使得分析结果的表达更加准确可靠。     

生物矿化法制备氧化镓颗粒及其性能表征

以蚕丝蛋白为模板,在相对温和的条件下通过生物矿化的手段形成具有特殊形貌的α-GaOOH颗粒,并通过在不同温度下煅烧α-GaOOH得到α-Ga2O3和β-Ga2O3.采用扫描电镜(SEM)、透射电镜(TEM)、X射线衍射仪(XRD)和荧光分光光度计(PL)等手段研究了丝素蛋白多肽和矿化时间对颗粒的影响,对其生物矿化机理进行了初步探讨.结果表明,所制备的β-Ga2O3具有优良的发光特性,丝素蛋白多肽模板以无定形的结构与产物结合在一起,并且经过高温烧结后仍以碳膜的形式包覆在材料的表面.这种碳膜结构对于提高材料的生物学性能起着重要的作用.